Remove all screws, essential oil threads, and the point of the established screws or threads, under the mind of the cap screws.
Insert screws into the holes that are threaded on the bushing side, since shown in Number 2. In sizes where washers are located beneath the screw head, make certain to make use of these washers. Please note that there should end up being one screw left over that’s not used when removing the bushing.
Tighten the screws alternately before bushing is loosened in the hub. If the bushing will not loosen instantly, tap on the hub to assist remove.
When installing or removing a Taper Lock bush, it is imperative that simply no lubrication be used between your taper. The presence of lubricant on the tapered surfaces is not attractive, as the taper bushing depends on friction to operate effectively, and lubricants reduce friction. use industry standard Part Numbers to recognize the specifications of every Taper Lock bush or Taper bush.
It’s the most successful shaft fixing in the market place today with a full selection of both metric and imperial sizes as well as a full selection of weld-on hubs, bolt-on hubs and hub adaptors.
Simple installation and removal
Equivalent to a shrink-on fit on uniform load applications and thus eliminating the cost of a key
No costly reboring: complete range of both metric and imperial available
Standard range suits up to 125mm/5″ shafts
Special 4-hole feature for balanced assemblies
Complete brief reach range obtainable, for compact lightweight assemblies
High grade, close grain iron (GG25) material
Spherodial Graphite (S.G.) iron building on some sizes to provide increase maximum bores
Manufactured from metal to provide convenient methods to secure fan rotors, metal pulleys, plate sprockets, impellers etc. to a shaft.
Shouldered outer diameter permits easy location
A convenient methods to secure fan rotors, metal pulleys, plate sprockets, impellers etc to a shaft
Welding not necessary
For use with parallel bore eliminating the expense of drilling, tapping and taper boring
Keyed version also available for heavy duty applications
Installation of a Taper Lock bush, including Martin or Fenner Taper Lock bush elements, is as follows:
Screws ought to be tightened alternately and evenly until all screws are pulled up and the bushing is square into the hub.
The Taper Lock bush must be thoroughly cleaned, removing all traces of oil, grease, dirt, and metal filings. Clean the shaft, the bore, the exterior of the bushing, and the bore of the hub in which the bush is usually to be set 
up into, making sure the bush is taken off the hub, should it currently be installed.
Verify the bushing to ensure all surfaces are free from nicks and burrs, and guarantee the bushing has no indicators of cracking or fatigue. Place the bushing in to the hub and match fifty percent holes to make finish holes. It is necessary to note that the holes need to be matched, not the threads. Each hole will end up being threaded using one side only.
Oil threads, the idea of the established screws or threads, and beneath the mind of the cap screws. After that place the screws loosely in to the holes that are threaded on the hub-side
Ensure that the Taper Lock bush is free of charge in the hub, then slip the assembly onto the shaft and locate in the required position. Insert the properly sized key into the shaft keyway, making sure the key is a press match the shaft keyway. Ensure there is an air gap between the top of the essential and the bushing keyway slot. This will prevent cracking of the bush. IMPORTANT: Make sure that there is no essential oil or lubricant between your taper externally of the bushing and the taper bore of the hub, to that your bushing is being installed.
Screws ought to be tightened alternately and evenly until all screws are pulled up and the bushing is sq . into the hub.
Using a hammer and prevent, or sleeve, against the large end of the Taper Lock bush will avoid harm to the bushing. Gently tap against the busing to ensure it is seated squarely. The screws are after that tightened additional. A torque wrench is used to tighten the screws alternatively and evenly until all of them are to the suggested torque setting.
Repeat this alternate hammering and screw tightening until the specified torque is achieved no longer requires tightening following hammering. IMPORTANT: Over time of running under regular conditions, it’s advocated that the application form be reviewed to guarantee the torque configurations of the screws are accurate, , nor need re-tightening.
Fill the holes that aren’t used in combination with grease or silicone sealant to avoid them from filling with dirt and/or rust.
Removal of a Taper Lock bush, including Martin or Fenner Taper Lock bush elements, is as follows: