The EP Series Helical Bevel Reducer provides unmatched performance, durability, and 
design flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft lbs).
The cat4CAD software allows simple interactive product selection of the complete gearbox and gear-engine system. Cat4CAD supports you in selecting and configuring these products, provides you the opportunity to print out comprehensive technical data bedding, and generates complete 2D drawings and 3D models for direct download.
11 sizes
Input power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Class 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and higher torques in smaller sized sizes.
Multiple Input Options: Essential gear motors, inch or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Options: Hollow bores and shrink disks for shaft mounting, inch and metric result shafts, mounting pilots and flanges provide an array of design solutions.
UNIBLOCK Housing: For helical bevel gear reducer maximum rigidity, universal mounting on five sides or via a torque arm.
Worldwide Motor: Multiple leads and windings for worldwide multi volt/Hz requirements in addition modular design to accept brakes, encoders or forced cooling.
High efficiency engine design available
Innovative self-locking, self-aligning taper shaft electric motor connection
Gearbox supplied factory filled up with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals on heat treated, plunge surface shafts
Shaft mounting choices include tapered bushings designs
This is a thorough offering of energy-efficient, right angle helical bevel enclosed gearing. It really is available as gearmotors and a number of reducers with torque capacities up to 119,000 inch pounds. Housing styles include footed, encounter and flanged configurations. Gearmotors can be found in three phase high efficiency designs through 50 HP and single phase to 5 HP. We provide a selection of input and result shaft choices. Additionally, you will see fixed and variable speed motors and selection of ratios obtainable in this product offering.
Features
Accommodates insight power from ¼ Hp to 75Hp
Torque rankings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers affordable high and low speed solutions
Up to 94% efficient
Four input options available for all units
Two output flange options – B5 and B14
Multiple output shaft interfaces
Essential dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
Heavy Duty Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the growing and varying needs of customers, you can expect an array of Helical Bevel Equipment Reducers. The technological content of our products allows for an extraordinary performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we offer are successfully found in a vast number of commercial and civil applications. They are B-Series units that offer excellent affordability and result torque/weight ratio, especially due to the fact they need very limited servicing. Besides these, our products are available in cast iron (sizes 063 to 163) or light weight aluminum (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for electric motor coupling, IB with input shaft, CB with compact motor, PB-fitted for electric motor coupling with flexible joint
Casing with feet FC, flange SC and general UC
Power up to 90 kW
Gears hardened and tempered with shaved or floor profile
Gearing with 3 reduction stages
Gleason spiral bevel equipment pairs with run-in profile, mounted as second decrease stage for an increased resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-strength casings optimized with FEM evaluation and input and output flanges of grey cast-iron G200 to make sure top level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, output flange, output shaft, shrink disk, backstop device, protection cover kit, viton essential oil seals, reinforced result, assemble/disassemble kit
Series EP right angle helical bevel gear motors offer ratios from 8:1 to 160:1 in three levels or up to 10000:1 in five phases. Motors are available up to 90kW and output torque capacity up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and will be offered with single or double extended output shafts.
Devices are also available as shaft mounted or with result flanges and are designed for installation horizontally or vertically. The products can also be provided with a bolt on torque response bracket and all variants can be found possibly motorised or with an input shaft assembly.
Adding to the brand new selection of Ever-Power helical equipment motors the product takes benefit of our a long time of accumulated design expertise together with the use of high quality materials and components. The outcome is a number of speed reducing geared motors providing high load holding capacities, increased efficiency, tranquil running and reliability.
Features of Helical Bevel Gear Motor
Standard motor connection
Capability to fit double essential oil seals, on insight and output shaft because required.
All units are dimensionally interchangeable with other major manufacturers.
Units are produced and assembled from a family of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units can be fitted with a backstop module and reducer Devices can be installed with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are used in industries such as chemical substances, pharma, packaging, food processing, plastic-type material and automation etc.
Key Features:
Sizes: A40-A50-A70
Offered versions: EP – fitted for motor coupling, IEP – with input shaft, CEP – with small motor
Cases with ft, flange or universal
Power up to 4,8 Kw
Gears with shaved or ground profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Superb mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in according to DIN 1843
Accessories: torque arm, result flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and made up of Y series engine, helical gear,Arc gear and worm gear. The gears are made from high wear-resisting alloy components, specially and finely processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact structure, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Small design, small volume, nice appearance ,and strong capacity to be overloaded.
6: Precise division and wide range for transmission ratio.
7: The effectiveness is up to as high as 96% with low energy consumption, strong adaptability and is capable of working continually in corrosive or damp environment.
8: All- purpose make use of, convenient and low-price maintenance.
9: New seal gadget, strong adaptability.
10: Varied range of motor combinations, mouting positions and struture projects.
